Fab-Factory - has a page up with some details on their N54 IM, it looks pretty sweet, here are some details:
$1895 for the standard billet design manifold, if you go top mounted injectors and rail, $2495. Prototypes ready approximately mid to late November.
![14958478_10206587451239775_1455962205_n.jpg 14958478_10206587451239775_1455962205_n.jpg](https://www.spoolstreet.com/data/attachments/0/37-4ce43ef6898141390b74f54ce3a535cc.jpg)
For further details, @A4RingedONE8T should be able to provide them!
Which do you think is better, a billet or cast intake manifold?
$1895 for the standard billet design manifold, if you go top mounted injectors and rail, $2495. Prototypes ready approximately mid to late November.
Manifolds will begin shipping late 16' Contact [email protected] for further information and ordering.
I have flow data for my own use on this plenum as shown above and all is good. About 5% deviation in distribution between highest and lowest flowing cyl @ 50psi (and to note cyl 6 is not the lowest one).
![14799772_10206570519816500_1007508698_o.jpg 14799772_10206570519816500_1007508698_o.jpg](https://www.spoolstreet.com/data/attachments/0/29-5b806ef8a2f2171fa580d740c220aec7.jpg)
![14872498_10206570519736498_506061757_n.jpg 14872498_10206570519736498_506061757_n.jpg](https://www.spoolstreet.com/data/attachments/0/30-2caf96d2cfbe4b9ed5fc76e1e08a3e52.jpg)
![14877173_10206570519536493_917544545_n.jpg 14877173_10206570519536493_917544545_n.jpg](https://www.spoolstreet.com/data/attachments/0/31-a16da3030c03004bd23b7bec7ca04e18.jpg)
![14914528_10206570519616495_785669737_n.jpg 14914528_10206570519616495_785669737_n.jpg](https://www.spoolstreet.com/data/attachments/0/32-72c1fd69d70fe3c44b9a562ba158317a.jpg)
![14924139_10206570519656496_1589625176_o.jpg 14924139_10206570519656496_1589625176_o.jpg](https://www.spoolstreet.com/data/attachments/0/33-bb7be8b626db9f8f764d2f318f170e9d.jpg)
![14937844_10206587451279776_161354413_n.jpg 14937844_10206587451279776_161354413_n.jpg](https://www.spoolstreet.com/data/attachments/0/34-f80e93828528df77a6afd38d6b7adceb.jpg)
![14954383_10206587451199774_880634584_o.jpg 14954383_10206587451199774_880634584_o.jpg](https://www.spoolstreet.com/data/attachments/0/35-6ccaa20c0aae0d0251a8ec0f5bec15e7.jpg)
![14954535_10206587451319777_1345907250_o.jpg 14954535_10206587451319777_1345907250_o.jpg](https://www.spoolstreet.com/data/attachments/0/36-716a2fd988407ac534c6a541539b1515.jpg)
![14958478_10206587451239775_1455962205_n.jpg 14958478_10206587451239775_1455962205_n.jpg](https://www.spoolstreet.com/data/attachments/0/37-4ce43ef6898141390b74f54ce3a535cc.jpg)
For further details, @A4RingedONE8T should be able to provide them!
Which do you think is better, a billet or cast intake manifold?