B58 Ignition Coil DIY solutions

Scorpstan

Corporal
Feb 27, 2017
111
130
0
Ride
335i
like this??
 

Attachments

  • 16285299558523808968758313621454.jpg
    16285299558523808968758313621454.jpg
    472.3 KB · Views: 124

Dumaurier7

Lieutenant
May 19, 2020
538
217
0
The circles on the right are the injectors and the pipe at the back circled actually rises up to meet the hood so there is a lot of room under it. I already have the coils on hand, tried them a while ago and they fit fine.
 

BriggTrim

New Member
Aug 19, 2021
1
1
0
Hi....the existence of the stock loops is a bit restricted at higher than stock strength and your situation will be unique. most say that they will wear out in some measure of miles. That may be 20k, 40k, 60k relying upon various elements. Assuming you run a blend of E85, more flash is most likely required, and so forth

In that sense my thinking is that I was because of redesign and getting a curl that has been tried to convey more flash when I intend to run e55 is a smart thought. My work was to make a moderate transformation choice for myself (and presently others).

www.7pcb.com
 
Last edited:
  • Funny
Reactions: Dumaurier7

NoGuru

Captain
Jan 9, 2018
1,204
589
0
Just North of Detroit
Ride
BMW 335is
Hi....the existence of the stock loops is a bit restricted at higher than stock strength and your situation will be unique. most say that they will wear out in some measure of miles. That may be 20k, 40k, 60k relying upon various elements. Assuming you run a blend of E85, more flash is most likely required, and so forth

In that sense my thinking is that I was because of redesign and getting a curl that has been tried to convey more flash when I intend to run e55 is a smart thought. My work was to make a moderate transformation choice for myself (and presently others).
1629372007811.png


I award you no points!

Maybe it is too early for me but I am not really sure what you just said.
 

JohnDaviz

Lieutenant
Jan 6, 2019
863
577
0
Ride
335i E92 DCT
It is already late here but no comprende either.

I think flash is spark and curl is something on the spring. But thats about it.
 

Scorpstan

Corporal
Feb 27, 2017
111
130
0
Ride
335i
did some runs with the b58 coils and my setup (resistor in boots) with the SPP223E boots.
with my old bimmerlife kit i had a liiiiittle bit more corrections.
log shows a 850WHP Run

next step is to test them over more gears wot and higher boost level.
 

Attachments

  • b58 coil test.jpg
    b58 coil test.jpg
    54.6 KB · Views: 102
Last edited:

ShocknAwe

Captain
Jan 24, 2018
1,470
1
728
0
Charleston, SC
Ride
N54/3 1er ///Mutt
did some runs with the b58 coils and my setup (resistor in boots) with the SPP223E boots.
with my old bimmerlife kit i had a liiiiittle bit more corrections.
log shows a 850WHP Run

next step is to test them over more gears wot and higher boost level.
What plugs and gaps is this with? I'm at 0.025" on S55 plugs with my PR kit ~600whp
 

Scorpstan

Corporal
Feb 27, 2017
111
130
0
Ride
335i
What plugs and gaps is this with? I'm at 0.025" on S55 plugs with my PR kit ~600whp

nkg racing sparks 9er cold grade. with 0.020 gap

with other project car which have s55 plugs 0.025" and PR kit too, we run 800whp at moment
 

pysical

Sergeant
Jun 16, 2017
471
108
0
Ride
2009 335xi E90
Awesome to see this working out well. I still need to trim up my resistors and put them in my boots.
 
  • Like
Reactions: Scorpstan

Krampus

Specialist
Aug 8, 2020
64
31
0
Finland
Would there be any recommendations for Europeans on what ignition coil boots could be fitted? For example, a CPBK206 set from Ebay would cost about $ 75 when shipped and including taxes.
 

Scorpstan

Corporal
Feb 27, 2017
111
130
0
Ride
335i
Would there be any recommendations for Europeans on what ignition coil boots could be fitted? For example, a CPBK206 set from Ebay would cost about $ 75 when shipped and including taxes.
Order the SPP223E from rockauto